The purchase price of a gear motor or reducer is only one part of its cost. Energy use, maintenance, failures, and production lost during downtime can make a lower-priced unit more expensive over its useful life.
A total cost of ownership (TCO) analysis compares options over the same period and under the same application conditions. This guide explains how to estimate the main costs and use the results to select an industrial gear motor or reducer.
Use standards to verify ratings and efficiency data, not to replace TCO analysis. For example:
Obtain supplier test data for the actual unit and operating points. Confirm the applicable edition and scope of each standard. A standard can help verify a claim, but it does not establish that a unit is the lowest-cost choice for a specific duty cycle.
To compare options:
Do not select a unit based on efficiency or purchase price alone. Equipment that is unsuitable for the application can increase energy use, maintenance needs, and failure risk.
A practical TCO model should account for:
Use the same analysis period for every option. A five-year comparison, for example, should include the costs expected during those five years for both alternatives. Keep the system boundary consistent: decide whether the analysis includes the motor terminals, the variable-frequency drive, the reducer, and site wiring.
Before comparing costs, confirm that each candidate can perform the required work. Record:
Use measured operating data where available. Nameplate power alone may not represent the load experienced throughout a shift. For applications with varying loads, divide operation into periods and estimate the power and hours for each.
For a reasonably steady load, estimate electrical input power from delivered mechanical output power and overall system efficiency:
[P_{\text{input}} = \frac{P_{\text{output}}}{\eta_{\text{system}}}]
Then estimate annual energy use:
[E_{\text{annual}} = P_{\text{input}} \times H]
where:
Annual energy cost is:
[C_{\text{energy}} = E_{\text{annual}} \times R]
where (R) is the applicable electricity rate per kWh. If the tariff includes demand charges or time-of-use pricing, estimate those charges separately.
For varying loads, estimate energy for each operating period and add the results:
[E_{\text{annual}} =
\sum_{i=1}^{n}
\left(
\frac{P_{\text{output},i}}{\eta_i} \times H_i
\right)]
Use efficiency data that matches the actual speed, load, and configuration as closely as possible. A rated efficiency figure may not describe performance across the full duty cycle. Include drive losses if a variable-frequency drive or other power electronics are part of the system. Avoid counting the same losses twice if the efficiency figure already includes them. When combining motor, reducer, and drive efficiency, multiply only series efficiencies that are defined at the same operating point and do not already include downstream losses.
Where practical, measured electrical input power can provide a useful check on estimates. Make sure the measurement covers the same system boundary for each option.
Suppose an application requires an average delivered output of 7.5 kW for 4,000 hours per year. Compare two systems with estimated efficiencies of 88% and 92%. At an electricity rate of $0.12/kWh:
The estimated difference is about 1,482 kWh, or approximately $178 per year at that rate.
This example is illustrative, not a guarantee of savings. Actual consumption depends on the load profile, operating hours, system configuration, and efficiency under operating conditions.
Use maintenance records for similar equipment whenever possible. Estimate the expected annual cost of:
A simple estimate of expected annual downtime cost is:
[C_{\text{downtime}} = N \times T \times C_{\text{hour}}]
where:
If planned and unplanned stoppages have different durations or costs, estimate them separately and add the results. Avoid double-counting repair labor or other costs that are already included in the maintenance estimate.
Estimate the initial cost for each option:
[C_{\text{initial}} =
C_{\text{purchase}} +
C_{\text{accessories}} +
C_{\text{engineering}} +
C_{\text{installation}} +
C_{\text{commissioning}}]
Also estimate end-of-life cost, net of any residual value:
[C_{\text{EOL,net}} = C_{\text{removal}} + C_{\text{disposal}} - R_{\text{residual}}]
Use the same scope for each option. If one option requires a larger foundation, additional wiring, a different coupling, or extra commissioning, include those costs.
A complete TCO comparison can be expressed as:
[TCO =
C_{\text{initial}} +
\sum_{t=1}^{L}
\frac{
C_{\text{energy},t} +
C_{\text{maint},t} +
C_{\text{downtime},t}
}{(1+r)^t}
+
\frac{C_{\text{EOL,net}}}{(1+r)^L}]
where:
If future costs are not discounted, set (r = 0) and sum the annual costs directly. Use the same service period and system boundary for every option. If costs are expressed in constant dollars, use a real discount rate; if they are expressed in nominal dollars, use a nominal discount rate.
The following example is illustrative only. It uses the energy results above and adds assumed maintenance, downtime, installation, and end-of-life costs over five years. Annual costs are assumed constant for simplicity; in practice, use year-by-year values where they differ.
Assumptions:
Undiscounted five-year TCO:
With a 6% discount rate and end-of-year costs:
In this illustrative case, System B has the higher purchase price but the lower TCO because its assumed maintenance and downtime costs are lower. The downtime assumptions dominate the result. If the expected failure frequency or downtime cost were much lower, the purchase premium for System B might not be justified.
For example, if the downtime cost were $250/hour instead of $750/hour, the discounted TCO would be approximately $71,400 for System A and $63,300 for System B. System B would still be lower in this illustration, but by a much smaller margin. This shows why assumptions should be tested before a decision is made.
Before making a decision, test whether the ranking is robust:
Select the option that meets the application requirements and has the lowest TCO under realistic assumptions. If the result changes easily with small assumption changes, obtain better data before deciding. For critical applications, the cost of a failure may justify a higher-purchase-price unit even when the simple payback calculation is not favorable.
A TCO result is only as useful as the data behind it. Keep a short record of:
This record makes the analysis easier to review, update, and compare with actual performance after installation.